Redcat Ascent Fusion RC Crawler Deep Dive - Things YOU SHOULD Do Before Hitting The Trail

Turtle Laboratories
Turtle Laboratories
2,827
0
Published 2024-04-06
In this video, we dive a little deeper into the Redcat Racing Ascent Fusion RTR. Ready To Run rigs are great, especially for beginners, but they also need some attention before they become a reliable rig. We go over some must-dos on this chassis, which also applies to other RTR platforms.

Turtle Labs Field Work Bench - tinyurl.com/2p874h9v
Video with more details on the Field Bench - bit.ly/3aq6ia5
Repair Stand Kit: tinyurl.com/4czmrn4b

15% OFF REPAIR STAND, FIELD BENCH AND FIELD BENCH ACCESSORIES, DISCOUNT CODE: YTTLFB

Redcat Ascent Affiliate link: www.redcatracing.com/collections/rc-rock-crawlers-…

Our Website: turtlelaboratories.com/
Facebook: www.facebook.com/turtlelabs
Instagram: www.instagram.com/turtle_laboratories/

Grease used (Lucas red "n" tacky) : amzn.to/3JEAZqj

Some Tools Used on this channel:
- Dewalt Gyroscopic Cordless Screwdriver: amzn.to/4alp7Fx
- Injora Hex Screwdriver Set: amzn.to/4aKmuNa
- Injora Nutdriver Set: amzn.to/3vIQn1E
- Vibra-TITE: amzn.to/3U4oxq2
- Red "N" Tacky Grease: amzn.to/3U5wYRL
- Files - amzn.to/3PTzG9d
- Precision Diamond Files - amzn.to/3jvafyB
- Proxxon Rotary Tool - amzn.to/3PQyMu8
- Proxxon Rotary Tool Power Supply - amzn.to/3YPCKYk
- My New Favorite Soldering Station - amzn.to/3vKH66v
- Dynamite Metric Hex Driver - amzn.to/3s279nM
- Dynamite Metric Nut Driver - amzn.to/3BzPsPC
- Hobbypark Work Stand - amzn.to/3s27qXQ
- Tekton Plier Set - amzn.to/3HhrWbd
- Vibra-Tite Threadlocker - amzn.to/3t5ZBzv
All Comments (15)
  • @duard8652
    Amazing! Want to do these even before running, while I don't need to wash the dirt and the dust off. And as everyone says, hat off to the stand. Video is great ❤
  • @Jerroldbubbataylor
    Thanks for the vid always like as much info as I can get about a rig or rigs. Knowledge is power
  • @BillsWorkbench
    Thank you for the information, I need to check out that repair stand.
  • @OGRadGrow
    Great info, especially on Redcat stuff. I had to do the same to my Gen 8. 👍🏾
  • @bradgourley2286
    Hey man great video.. Did it take anything smaller than the 1.5 mm tool for any of the screws? I ask because I was trying to get the axle end screws out and my 1.5mm seemed to big lol
  • @Casitascrawlers
    Mine is arriving today thanks for the tips. And where did you get that stand love that thing.
  • @sprather84
    Great video and that stand is amazing. I was looking on your website I don’t quite see it. Can you put a link in there? I love how it adjusts.
  • @heydaddy61
    Very informative. I appreciated your camera angles. All too often videos are just overhead and limit what is visible
  • @axellness
    got s link to the stand youre using?