How-to Bind v3.4 Express LRS Receivers • All 4 Methods [ELRS]

RC Video Reviews
RC Video Reviews
3,568
0
2024-05-28に共有
There are 4 ways to bind Express LRS receivers as of v3.4. In this video, you'll see all 4. This video is time indexed so you can jump around to the method you need.

00:00 Intro
00:09 Option 1: BetaFlight
01:57 Option 2: Binding Phrase
04:46 Option 3: Bind Button
05:32 Option 4: Power Cycle

REFERENCE LINKS
► ExpressLRS Wi-Fi Explained:    • Express LRS Wi-Fi Modes Explained  

RCVR LINKS
► Support the work I do here on Patreon: patreon.com/rcvideoreviews
► RCVR MERCH rcvr.myspreadshop.com/
► Discord - Hang out with the RCVR Crew: discord.gg/jSFTASU

AFFILIATE LINKS
► Amazon Affiliate: amzn.to/3lEz5ZL
► Banggood Affiliate: www.banggood.com/custlink/3DDRJ4cBuV

#RCVideoReviews #expresslrs #elrs
コメント (19)
  • @CapnBry
    If someone can't bind their receiver after these great instructions, I feel bad for you, son 😅
  • @Mr.Laidukas
    Thanks for your videos, you inspire me to make ELRS videos in my native language to make it more popular among old school guys that are ignoring this part of the hobby.
  • @dronebotvijay3566
    Woow all methods to Bind the receiver and transmitter covered in this video. Thanks for replying 🙏
  • @MrZeek101
    4 ways to skin a cat amazing as always John you pretty much bound all 4 ways in the time most bind once Take Care
  • @JyeSmith
    You should be able to use the Bind button in the BF receiver tab. No need for cli commands. You might also like to cover the volatile binding option found in the Rx Lua.
  • @andrewtaylor5103
    Just a tip, if its not binding check that the rx is compatible with the packet rate you have set in the radio. Took me forever to figure that out with one of my quads
  • @MatCron
    If you open ELRS configurator and then connect RX via wifi, you get a pop up and all fields will be filled in automatically, wonderful.
  • @RubyS.1
    Express lrs continues to impress me. Hopefully somebody comes out with additional sensors at some point
  • @ApappieK
    Just wondering, I fly my ELRS quads and planes with 2 TX-es with the same binding phrase. Using a binding phrase, I don't have to bind again if I use the other TX. Binding using the other possibilities, like the button, will require a new binding in case I switch to the other TX?
  • @giuseppe.marino
    Great video as always, I know it isn’t pertinent with this video but, I need help about edgetx. I have a mt12 surface radio and what I want to do is when I set for example the steering trim to -60, I would be able to reach +100 and not just +40 when I move the steering wheel the other way around. I tried to set the weight to 200 in the mixes page but this way I would reach the 100% steering with only the 50% of rotation of the steering wheel when the trim is centered. thank you in advance.
  • @dronepilot260rc
    The method I use is similar to method 2 . I use the configurator and then save the file to my ELRS folder. Next I power up my receiver using a servo tester and wait the 60 seconds until it goes into WiFi mode. I then get on my computer 🖥️ and click on the expresslrs WiFi signal and then I update the RX using the ELRS folder that has the bind phrase ect. After that it’s ready to go 🎉
  • @Retset
    I don't use ELRS purely because I have more receivers than aircraft (I bought a lot of R168's when they came out). However, I'm thinking it would be a good project as I always feel happiest on the craft that have Crossfire. A question: Methods 3 and 4 were so so simple, what are the advantages (if any) to Method 2?
  • @Midwest-RC
    What if there is no bind button only a boot button?